Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
STM32H7 PCB Design Review – What Are the Most Common Layout Mistakes?
Hi everyone,I'm designing my first custom PCB around an STM32H7 microcontroller and would appreciate some advice before sending it for fabrication.The board will run at high clock speeds and includes:STM32H7 MCUExternal QSPI FlashEthernet PHYTFT disp...
Unable to open the PCB file of the STM32H743I-EVAL board
Post split from this thread. Hi Thank you for your response. I have downloaded the CAD files you shared for the STM32H743I-EVAL board from the STMicroelectronics website. I was able to open the schematic file successfully in Altium. However, I am ...
Resolved! STM32 interface with eMMC
Hi,We are currently developing board using the STM32F765 microcontroller and eMMC memory (part numbers: MX52LM08A11XVI and IS21ES08GA-JCLI) via the SDMMC interface in STM32Cube.Can you help us determine if the MX52LM08A11XVI and IS21ES08GA-JCLI can i...
Request for Review of STM32N657 Power Supply Schematic
Dear Team,I am new to the STM32 platform and currently working on my first design using the STM32N657X0H3Q.I have attached the power supply section of my schematic and would appreciate if you could review it and provide feedback, especially regarding...
Target No Device Found: SWDIO (PA13) at 0V on STM32L073CZT Custom Board
Hello STM32 Community, I am facing a persistent "Target no device found" error when trying to program an STM32L073CZT3 custom board using a Nucleo-L073RZ as an external ST-LINK (CN2 jumpers removed). Hardware Setup: MCU: STM32L073CZT3 (custom PCB) ...
Resolved! Nucleo-F446RE GPIOs and accorindg HW Board Pins naming ??
Hello,rather simple issue I have, I am trying to figure out the connection between the actual port naming on my board and the GPIOs defined within Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h for example. I cant find the reference, where are...
Resolved! Something is not working?
I am debugging my program on a NUCLEO-H533RE and it fails at:{ uvalRAM.RAMROM[i] [x] = uvalFla.FlaROM[Page] [x];}which is moving a byte from flash to RAM. The dissemblershows it stopped at08000d2c: b.n 0x8000d2cBreak at address "0x8000d2c" with no de...
how to flash code on NUCLEO-H753ZI using external ST-link
Title edited to make clear that this is talking about a NUCLEO-H753ZI board.I wanted to upload/flash code on my STM32H753zi MCU using external ST-Link ....how to bypass the onboard st-link connections
Use STLINK-V3SET with & without B-STLINK-ISOL ?
Title edited to clarify that this is about using the STLINK-V3SET with & without the B-STLINK-ISOL adapter board.hi , is there a easiest way to shift the STLINK v3 from ISOL to normal , during debugging it is ok with ISOL as the device has power.but ...
RealTerm Not Showing Output from Nucleo N657X0Q Board
Currently, I am using the Nucleo N657X0Q board, and I am facing an issue with getting my machine learning model output on RealTerm. I am unable to see any output. Does anyone know how to resolve this issue?
