Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Resolved! Is there an STM32 USB pen drive board with pin only for UART serial comms ?
hello ST Community,There's an STM32 board in a USB pen drive format with a small flash memory capacity and only a few pins (3-5 pins) for UART serial communication. On this STM32 board, inside the USB pen drive, I can program the dedicated software f...
Resolved! H755: Need to erase full chip flash memory after every powerloss to the board
Hello i'm new to STM32, i'm doing school project on in. Basically the plan is to read oil temperature from CAN bus in car, and display the temperature on analog clock using servo. I have the H755ZI-Q board for this. I know it's bit overkill for what ...
Resolved! STM32F103RB Nucleo – Debug fails after programming (“Target is not responding” in ST-LINK GDB Server)
Hello,I am working with an STM32F103RB Nucleo board. I am able to successfully connect and program the device using ST-LINK, but I am facing an issue during debugging.The code is downloaded successfully and verified, but when the debugger tries to ru...
Multiple Expansion boards on STM32L073RZ-Nucleo
Hello I've been using a STM32L073RZ-Nucleo with a X-NUCLEO-IOD02A1 to test some functions and it works great. But the thing I'm wondering is if its possible to also add X-NUCLEO-PLC01A1 expansion board while using X-NUCLEO-IOD02A1 at the same time. ...
Resolved! LCD screen want work in my STM32F407DISCO Location : stm32mcu boards and hardware tools
Hello, I have 2 boards an STM32F407 disco and an STM3F746DISCO and i want to create a project that implements an external LCD screen to the board however when the project runned well with the F746 the screen didnt work with the F407 any guidelines?
Resolved! Help starting testing STM32H747I-DISCO on MacOS / Apple Silicon
Hello,I've just received my fresh new SMT32H747I-DISCO dev board and I wanted to try some samples.I have some experience deveolping on embedded Liuxes, but this is my second MCU (the first one was a Raspberry PICO, don't know if this counts). I am us...
Resolved! ST-Link Error With Riverdi Display And STM32H757XIH6
I have this Riverdi board with a STM32H757XIH6 microcontroller. I have been using it consistently and loading touchgfx programs on it. Today I was trying to use the 40 pin header and program one of the gpio pins on it to act as a gpio output. I put ...
Resolved! PA1 Voltage Level in Reset State – Nucleo-F446ZE
Hello, While using the Nucleo-F446ZE, I observed that pin PA1 remains at approximately 2.6 V during reset, even when an external pull-down resistor is applied. On this development board, PA1 can be configured as the RMII Reference Clock. However, I...
Resolved! STM32H5E5 NUCLEO BOARD and Samples?
Hi, I would like to know when samples and kits for the new STM32H5E4/5E5 will be available.I already asked my local distributor this question, but they didn't know the answer. Ari
Resolved! STM32G491 USB for data only
Hi, I'm developing a custom STM32G491CEU6 board with USB-C and pins for external ST-LINK programmer. Board is powered from external source. I connected only D+, D- and GND from on USB-C to MCU, because I wanted to use this only for debug. Right now t...
