Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Connection & Programming issues with ST-Link/V2 ISOL
Hello,I have been working with a Nucleo eval board and have not had any problems with the ST-Link connection. Recently I got an ST-Link/V2 ISOL dongle to use with a custom board using the same chip, and have been unable to connect with it. There seem...
What is the specific part number used as the pin headers for nucleo 144 boards?
I want to stuff the extra connectors so that I can plug the nucleo onto a backboard, but I want to make sure that they are the same length.. I have been unable to find what appear to be compatible connectors in stock anywhere?. This has to be a fre...
STM32F427VIT6 flash mode
Hello, I have a custom PCB with STM32F427VIT6. Been reading and learning a lot about MCU's in general. I'm very new to all of this so please bare with me.When PCB is connected to the PC via usb, it shows up as HID device (it emulates gamepad/controll...
CanBus Communication between Nucleo STM32F446RET and RaspberryPi5
Hello, I'm working on a canbus project and I'm trying to read some data on the nucleo to confirm that my hardware setup works good since it's not a common use. At this point:- MCP2515 communication via SPI with the RPI5 and it's well configured. - I...
Resolved! STM32H747I-DISCO built-in display issue
I am working on a project using the built-in LCD display of the STM32H747I-DISCO board. However, the display output shows unintended thin lines and color distortions, appearing as if the colors are breaking. I am unsure whether this issue is caused b...
Resolved! STM32N6 Nucleo - Interrupt loop preventing bootup
Good day Folks,I am trying to get a simple program working on the STM32N6 Nucleo board, however when debugging an interruptoccurs causing the code just to get stuck in the Default Handler.I am not sure what interrupt is triggering it.This is most lik...
Camera not detected with STM32N6570-DK and VD66GY S-BOARD
Hi,STM32N6570-DK preloaded code works with the default MB1854B camera board. My question is:"Does the default firmware support VD66GY?" I tried and could not make it work.When I switch the camera module to VD66GY S-BOARD, the LCD shows "Camera not de...
"The interface firmware FAILED to reset/halt the target MCU"
Once I connect st-link v2-1 to STM32G473VBT6, there is a disk added into my PC, and there are 2 files in the disk. One is DETAILS.TXT(Version: V2J37M26 Build: May 13 2020 17:07:43), another is FAIL.TXT (The interface firmware FAILED to reset/halt t...
Resolved! Connect to USB pins directly using NUCLEO-G071RB
Dear community,I have a nucleo board NUCLEO-G071RB and I would like to use the Build-In USB in the STM32G071, is there a shield or an expansion board compatible with this nucleo board, that allow me to access to the USBThank you in advance.Best regar...
Resolved! STM32U5G7VJT6Q GPIO Input issue
Hi,I'm using the STM32U5G7VJT6Q microcontroller to read input from a few switches. All switches should show a high state when unpressed (due to the pull-up resistor) and a low state when pressed (grounded).However, one switch is acting strangely:When...
