Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Resolved! Is it mandatory to power STM32G473 from 3.3v only when I need in USB functionality?
I am going to use STM32G473 for my application. Most of peripheral interfaces need in 1.8v power (QSPI, I2C, GPIO, etc.) but i need in USB device functionality too.There is a requirement form data shhet (DS12712 Rev3 p174) to power USB tranciever fro...
Hi all, i am using a STM32 Nucleo-144 developement board with the STM32F429ZI MCU and i am powering it with a 5V Battery. In the Datasheet it says that Pin7 is a 3.3V output. Can i use this Pin to power a Sensor?
I am referring to this datasheet (page 52) : https://www.st.com/resource/en/user...ucleo144-boards-mb1137-stmicroelectronics.pdf
Debugging probe StLink V3 MINI vs MODS ? Why MODS does not work via CN5 connector?
Hello, I bought the StLink V3. The MODS version. The idea was to have good, handy and slim debugging probe. Well isolated as housed in thermally shrinking tube. I equip all my Stm32 pcbs with the miniature debug connector comprised of: Gnd, SwCk, SwD...
STM32F446 and ST-Link debugging all of a sudden stopped working with IAR 6.50 but STM32F334 still working
Hello comrades...I have been using IAR 6.50 for a few years now with STM32F446VC 1-- pin uC and things have been working flawlessly. I also have more recently had a project using the STM32F334 controller and debugging just fine.Last week, all of a su...
MacOS "No ST-Link detected!" on stm32cubeide
After the update, I was unable to run or debug on my nucleo-l053r8 on MacOS Big Sur V11.4.
STM32F407VG SPI2_CLK
clock of SPI2_CLK pin effected to other GPIO as noise. i want to remove this noise. of course not effected because of board design i am already checked it.
STM32L100RC - CDC device
Hi,I'm trying to make a STM32L100RC work as a CDC device as shown on this website : https://damogranlabs.com/2018/02/stm32-usb-cdc/Nevertheless, it didn't work for me, even when I used the exact same file shared on the website. The USB is always dete...
Resolved! Debugger connection lost. Shutting down... monitor flash mass_erase didnt help
Hello,Im just starting with the nucleo board STM32L476RG using mac (10.13.6) and cube IDE 1.6.1. I also updated the firmware on the ST-link to the newest one when prompted.For the very first program I just wanted to make it blink to see if it works, ...
Resolved! Keil ARMCC V5.1 does not connect to Nucleo 474 (ST-LINK V3)
Is there any way to come around this? Or is this some "dirty trick" of the stupid "STM-Cube-Fan-Group" at STM to force all STM users into their stupid STM-Cube world?(If I try to connect Keil uVision 5.1 to the new Nucleo ARM G474 boards, the Keil Pr...
10-pin debug connector and STLINK-V3-ISOL - not reliable?
I am using STLINK V3 with the ISOL board, and using the supplied 10-core cable, going to this connector in my 32F417 targethttps://peter-ftp.co.uk/screenshots/202105072011602908.jpgOn the target connector, I have pins 3,5,7,9 grounded.Pins 2,4,6,10 g...
