Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Can I Use ST-LINK/V2-1 from Nucleo-F446RE to Program an External STM32 MCU?
I have an STM32 Nucleo-F446RE, which comes with an integrated ST-LINK/V2-1 debugger. I would like to use this ST-LINK to program an external STM32 MCU that does not have a development board.I checked the Nucleo schematics, and I see that ST-LINK/V2-1...
Resolved! STM32H753ZI Nucleo board with USB_OTG_FS communication
I'm using the STM32H753ZI Nucleo board with USB_OTG_FS communication,and I have enabled VBUS_SENSING. I would like to detect when the physical connection is lost,but I am not sure how to do it.Could you kindly provide any reference materials or guid...
VFD development boards
looking to learn VFD is there any development boards related to VFD
How to connect STM32F103C8T6 to STLINK-V3MINIE
I recently bought a Blue Pill, STLINK-V3MINIE and an adapter. How do I connect them together correctly?
Resolved! How connect SWDIO?
Hello. I was recently advised that STM32F103C8T6 and STLINK-V3MINIE should be soldered directly without an adapter. VCC with 3V3GND with GND SWDCLK with CLK SWDIO with ?
I can't use the ST-link in STM32CubeIDE even after updating the ST-link firmware
I am trying to debug the STM32C8T6 with st-link and STM32CubeIDE, following errors happened, I need help to solve this problem,"STMicroelectronics ST-LINK GDB server. Version 5.5.0Copyright (c) 2019, STMicroelectronics. All rights reserved.Starting s...
Resolved! STM32F746G-DISCO: ST-Link Port Broken, No Exposed SWD Pins, No Boot0 Pin
I’m working with an STM32F746G-DISCO board, and I’ve encountered an issue with the board. The ST-Link port is broken, and unfortunately, it cannot be soldered. To make matters worse, the SWD (Serial Wire Debug) pins are not exposed on the board, and ...
Request for Altium Designer Files for STEVAL-STMODLTE
Hi everyone,I’m working on a project involving the STEVAL-STMODLTE expansion module and was wondering if anyone has access to the Altium Designer project files (schematic and PCB layout) for this board. It would be really helpful for integration and ...
Resolved! Confusion Between HSE Clock Value in the Schematics on STM32L4R9I-EVAL Board and user manual
Hello Community,I have been working on CAN for two days, and I haven't been able to figure out the baud rate issue I'm facing. I'm using the HSE as the clock source with a value of 25MHz, as mentioned in the UM2248 document (I'm using the STM32L4R9I-...
Can't Connect to UART With STM32 Nucleo L476RG
I just started using and learning how to use the STM32 Nucleo L476RG Board. I am trying to integrate UART into STM32 to display text in Tera Term by using this guide (https://wiki.st.com/stm32mcu/wiki/STM32StepByStep:Step3_Introduction_to_the_UART).H...
