Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Resolved! Unable to Get Core ID - No STM32 Target Found - ST-LINK V2 Issue
Hello ST Community,I am facing an issue while trying to connect to my STM32 MCU using STM32CubeProgrammer and ST-LINK V2.Here are the details:ST-LINK SN: 50FF73064977875712192367ST-LINK Firmware Version: V2J45S7Error Message:Error: Unable to get core...
Resolved! STLINK-V3MODS for custom PCB
Hi Community,I'm designing a custom H755 board and had intended to implement my own USB-C with debug/programming interface using an external STLINK module. STLINK-V3MODS is a nice alternative way forward but I note from the user manual (UM2502) that ...
Error in initializing ST-LINK device. Reason: (9) Target not halted.
Hello everyone, I'm new to this topic, and I'm needing help with an error that got me stuck.I have a development board with a STM32F401CCU6 MCU. Until now, I had been doing exercises without problems in stm32cubeide. The problem was when I wanted to ...
Resolved! How to get more information about the LCD of the STM32N6570-DK kit
I am trying to show a picture on the LCD of the STM32N6570-DK kit. And I want to make sure that the LTDC peripheral can directly control the LCD's demonstration and it do not need and do not contain any other ICs except the Touch control IC, right? A...
Could I get SCHLIB files or pspice model for Nucle-F103 (MB1136)?
Dear all,I downloaded the schematic files for nucleo-64board(MB1136) from this page(https://www.st.com/en/evaluation-tools/nucleo-f103rb.html#cad-resources)and opened them in Altium.However, when I tried to run a simulation, I encountered an error.I ...
Resolved! stm32 MCU flashing via i2c
Hi,I'm working on flashing an STM32 MCU via I2C. The current setup involves a processor (host) and an STM32 MCU (G491RET6), where the processor needs to upload firmware to the MCU and perform flashing over I2C with the STM32 acting as the slave.I hav...
Resolved! Problems connecting ST-LINK V3 and STM32F103C8T6
Hello. I have a weird problem connecting a purchased V3 emulator to a blue pill board with STM32F103C8T6.I have:1) STLINK V3 original emulator (tested two copies from the same batch, with different firmware: the latest firmware from the site and the ...
Resolved! More details on using the Nucleo ST-Link to program other stm32
Are there any example on how to configure the ST-Link on the Nucleo-64 to be use? In particular the Blue Pill. A real life example may answer some questions I have after reading the document.Some things I read you only have to pull the CN2 jumpers i...
Resolved! Verify Failed when programming stm32f103c8 blue pill
Trying to program stm32f103c8 blue pill using st link v2 adapter on ac6 eclipse platform.but showing following error.embedded:startup.tcl:476: Error: ** Verify Failed **
Resolved! Blue-Pill/ST-Link Reports: Debugger connection lost. Shutting down...
I have followed Video "STM32CubeIDE basics - 03 GPIO HAL lab" as closely as possible for my hardware as closely as possible and get the following results in the console:STMicroelectronics ST-LINK GDB server. Version 5.5.0 Copyright (c) 2019, STMicroe...
