Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Wake up Nucleo L432KC from Standby mode with external RTC
Hey guys,i am a new member. I am using the Nucleo L432kc board for my masters thesis. I want it to work with the lowest power consumption can me. I am using an external very low power RTC, and i am trying to programm it to wake the board up every 30 ...
Need a library to get an RC522 RFID reader to interact with an STM32F746-DISCO board.
Hello there, As the title says, I'm trying to get an RC522 RFID reader to work with my STM32F746-DISCO board for a school project. I just wanted to know if anyone had any libraries they could share to help with this. My current objective is to toggle...
UART Transmit Data to PC Problem - NUCLEO-H755ZI-Q
Hello, I am new to STM32 and need help with UART. In recent days I have been trying to deploy my own neural network model on NUCLEO-H755ZI-Q development board. Through ST Edge AI Developer Cloud, I have generated my own CUEB IDE project. In the IDE p...
Resolved! Pinout question of STM32H723ZG board
Hello,UM2407 is the user manual of the STM32H723ZG Nucleo-144 development board. Likewise, the schematics of this board are available as https://www.st.com/resource/en/schematic_pack/mb1364-h723zg-e01_schematic.pdf.In both the manual and the schemati...
Resolved! timer 3 CNT not resetting upon elapsed period with an ARR of 4
EDIT: My apologies, it turns out that since i had auto reload preload enabled and was not setting the CNT back to 0, the timer would keep counting up until a rollover. I wrote a test program to test a 5 ms PWM single pulse output with a 3-timer mast...
STM32 drivers on windows11
HI , I m using stm32f103c6 32k board for my project competition , currently i m using windows 11 i have updated the bootloader , Maple003 driver visible on ports section in device manager but it throws error 10{could not able to start], i had tried m...
Resolved! programming using CLI taking a lot more time than using ST-LINK utility
Hi everyone,First, here is my set up:computer: windows 10uC: STM32F030K6T6flashing/debugging hardware tool: ST LINK v2 ( from nucleo board)I have noticed that it takes almost 30 secs to do same operation using CLI (wether directly launching a batch f...
Wrong wiring for SPI? and SPI (MISO) not responding
Hello to everyone,Were to start? Let me first try do describe the setup.1. Using and STM32F446 chip on a custom board. The board has 2-32pins slots: Slot A and B.2.For communication I'm using the SPI protocol.3.For slot A using PE12(CKL); PE13(MISO)P...
Resolved! SPI SSD1306 and I2C MPU6050 on stm32f103c8t6
Hello, I'm relatively new to the stm32cubeIDE and currently using it to program a self balancing robot using an stm32F103C8T6 chip.My current issue is that when i run the SSD1306 OLED display through SPI I am able to display graphics and text as requ...
Resolved! What type of connector for stlinkv2?
What is the name of the connector used on stlinkv2 programmers like this one? I can use single wires taped together, but hoping there's a standard cable or connector type that will connect better than single header pins taped together.
